
An LTL invoice bills 4,770 pounds on a shipment your dock scale recorded at 3,419. The bill is correct. Chargeable weight is the figure a carrier actually rates, and the governing tariff decides how it's computed. In this case the carrier applied a density floor and rated the cube, so 4,770 is a calculated number that was never meant to describe what the freight weighed.
Your audit probably has no rule for that line. It compares billed weight to tendered weight, finds a gap of 1,351 pounds, and does one of two wrong things: it flags a correct charge as an overbilling, or it releases the line because the rate per hundredweight looks right. The invoice uses one word, weight, for at least three different quantities.
How chargeable weight gets calculated
If you're working out how to calculate chargeable weight, start from two numbers: the weight you tendered and the weight the governing tariff rule produces. The carrier rates the greater of the two, and three mechanisms produce most of those rule-based figures:
- A density floor. The carrier measures the space the shipment occupies, multiplies by a minimum density, and rates the product. Scale weight drops out entirely.
- Deficit weight. The shipment is rated at the minimum of a higher rate break because that band prices cheaper, and the pounds you didn't ship appear as their own line.
- Dimensional weight. Volume divided by a published divisor, billed whenever it beats the scale. It's standard in parcel and air, where the divisor is the whole argument.
Each one is legitimate and published. None of them lives in the document your team treats as the rating authority, and no two carriers write them the same way.
How Does a Density Floor Affect Chargeable Weight?
A density floor is one answer to why your LTL invoice weight is higher than the scale weight: the carrier stops rating what the freight weighs and rates the trailer space it fills.
What PittOhio's Item 605 says
PittOhio's rules tariff Item 605, Minimum Charge Based on Cubic Capacity and Density, sets two triggers. Freight with an average density under 3 pounds per cubic foot that requires at least 350 but less than 750 cubic feet of trailer space is rated on a calculated weight of 6 pounds per cubic foot, at the customer's class 125 rate. Freight under 6 pounds per cubic foot that requires 750 cubic feet or more is rated the same way.
The item carries its own example. A shipment found to occupy 795 cubic feet at a density of 4.3 pounds per cubic foot is rated on a calculated weight of 4,770 pounds. At 4.3 pounds per cubic foot, 795 cubic feet holds about 3,419 pounds of freight; at the 6 pound floor it becomes 4,770. So the carrier bills 1,351 pounds of air by rule, and it overrides the commodity's class on the way past.
The provisions that settle more disputes than the thresholds
Cubic capacity is found by totaling the cubic feet of all articles, pieces and packaged units under NMFC Item 110. The number is assembled from handling units. Nobody measures it across the load.
Packaging matters too. Where it's insufficient, the height of the article is taken as 96 inches, the inside height of the trailer, however tall the freight actually stands.
The thresholds change from carrier to carrier
Old Dominion's accessorial brochure places its Minimum Charge for Low Density Freight, Item 610-1, at under 3 pounds per cubic foot between 350 and 749 cubic feet, or under 6 pounds per cubic foot from 750 cubic feet up. It handles capacity loads separately under Item 390, at 20 linear feet or 20,000 pounds. Saia's 170-D rules tariff sets its lower tier at under 4 pounds per cubic foot across the same 350 to 749 band.
That means one skid of insulation can stay under the rule at one routing guide position and get recalculated at the next. The version we see most often on invoices is a density floor that's been disputed as an overweight error while the tariff item itself was never opened.
Deficit weight bills pounds you didn't tender
The second mechanism runs the other way, and it usually works in your favour. Class rate scales price lower per hundredweight as weight rises. A shipment sitting just under a break can therefore cost more than the same freight rated at the minimum of the break above, so rating engines bump it.
IBM's documentation for deficit rating in Sterling walks through the arithmetic with sample breaks of 0 to 499, 500 to 999, and 1,000 to 4,999 pounds. A 495 pound shipment rated inside its own band prices at 4,950 dollars. Rated at the 500 pound minimum of the band above, it prices at 4,000. The engine returns the cheaper figure and shows the 5 pound difference as a deficit line.
What that does to your weight check
The invoice now carries a weight nobody tendered. Any check matching billed pounds against shipped pounds fails on that line by design.
You also have to test the bump in both directions, because you're owed the lower of the two results. A line rating 495 pounds inside the 0 to 499 band, when the band above prices cheaper, is an overcharge whose arithmetic looks clean on its face.
Dimensional weight works from a published divisor
Parcel and air derive dimensional weight from volume instead of a minimum density: length times width times height, divided by a published divisor. The carrier bills that figure as the chargeable weight whenever it beats the scale, so the divisor decides the bill.
Parcel: the USPS rule for July 2026
The USPS final rule for July 2026 domestic competitive products moves the dimensional weight factor to 139 and rounds length, width and height up to the nearest whole inch. It covers Priority Mail Express, Priority Mail, USPS Ground Advantage and Parcel Select. Volume at or under 1,728 cubic inches stays exempt.
Going from a 166 divisor to 139 lifts billable weight on an unchanged box by about 19 percent. The rounding adds more. A carton measured at 18.1 by 14.2 by 10.3 inches bills as 19 by 15 by 11, which is 3,135 cubic inches against the 2,647 you shipped, or 23 billable pounds where the measured volume gives 20. In parcel-heavy networks, like the ones covered under freight audit for retail shippers, that rounding rule deserves its own check.
Air: the IATA rule in metric
The IATA TACT rules at section 3.9.4 charge a consignment on volume once its average dimensional figure exceeds 6,000 cubic centimetres per kilogram. That works out at 166 cubic inches per pound. The divisor USPS has just retired and the international air standard are the same ratio in different units.
| Mechanism | What sets it off | Where it's written | What to check |
|---|---|---|---|
| Density floor | Cube and density cross a carrier threshold | That carrier's rules tariff, outside the NMFC | Measured cube, the threshold table for that lane, any class override |
| Deficit weight | Actual weight sits below a cheaper rate break | Rating engine logic on the rate scale | Both outcomes computed, the cheaper one billed |
| Dimensional weight | Volume over the divisor beats the scale | Carrier service guide or air waybill tariff | Contract divisor, rounding rule, dimensions used |
How Penny checks a chargeable weight line
In our automated freight invoice audit, Penny starts by asking which mechanism produced the billed number. A billed weight that differs from your tender isn't a variance yet.
Where a floor applied, she rebuilds it on the carrier's own figures: cube totalled from the handling units, the minimum density and class in the tariff item governing that lane, and whether the thresholds were actually crossed. A shipment at 760 cubic feet and 6.2 pounds per cubic foot sits above the line and rates on its scale weight. She also tests the 96 inch substitution, which depends on packaging and doesn't apply automatically.
Where the line was bumped, she computes both bands and confirms the cheaper one was billed. Where volume drove the charge, she checks the divisor against your contract instead of the published default. A negotiated divisor is a common term, and rating systems don't always carry it.
Where your tender holds no measured dimension for the handling unit, she won't construct one. The line comes back marked needs-data with the field named, as described in why an agent should say it needs data instead of guessing. A cube you can't evidence loses for the reason set out in defending freight class without recorded dimensions: the carrier measured, and you only asserted.
A test for one quarter of LTL invoices
- Pull every line from the quarter where billed weight differs from tendered weight by more than five percent.
- Sort each line into density floor, deficit bump, or genuinely unexplained. The last group is usually the smallest, and the density floor group is the one nobody has priced.
- Work the density floor lines against the governing tariff item and ask whether the thresholds were really met.
That last step is what separates a rule correctly applied from one applied to freight that never triggered it. If you'd rather see it done than do it by hand, book a walkthrough with that quarter's invoices and we'll run Penny across them live, naming the mechanism behind every billed weight.
Frequently asked questions
- What is deficit weight and how is it calculated?
- Deficit weight is the gap between what you shipped and the minimum weight of a higher rate break, billed because that heavier band prices cheaper. The rating engine prices the shipment inside its own band and at the minimum of the band above, then bills the lower total. In IBM's Sterling example, a 495 pound shipment prices at 4,950 dollars in its own band and 4,000 dollars at the 500 pound minimum, so the invoice shows a 5 pound deficit line.
- How is dimensional weight calculated in freight shipping?
- Dimensional weight is the shipment's volume divided by a published divisor, and the carrier bills it whenever it beats the scale weight. The USPS rule for July 2026 uses a factor of 139 and rounds each dimension up to the next whole inch. Air freight under the IATA rules charges on volume once a consignment exceeds 6,000 cubic centimetres per kilogram, which works out at 166 cubic inches per pound.
- How can businesses audit chargeable weight on freight invoices?
- To audit chargeable weight in LTL shipping, first identify whether a density floor, a deficit rating or a dimensional divisor produced the billed number. Rebuild it from the carrier's own figures and the tariff item governing that lane, and confirm the thresholds were actually crossed. For deficit lines, check that the cheaper of the two bands was billed, and for dimensional weight, check the divisor in your contract rather than the published default.
- How is chargeable weight calculated for LTL freight?
- Chargeable weight is the figure the carrier's tariff tells it to rate, which can differ from scale weight. A density floor rates the measured cube at a minimum density, and a deficit rating bills the minimum weight of a cheaper rate break. On PittOhio's Item 605 example, 795 cubic feet at 4.3 pounds per cubic foot is rated at a calculated 4,770 pounds.
- What is the difference between chargeable weight and actual weight?
- Actual weight is what the scale records when the freight is tendered. Chargeable weight is what gets rated after the tariff's density, deficit or dimensional rules are applied. The two can differ legitimately, so a gap between them is a reason to check which rule applied rather than proof of an overcharge.
See it on your freight
Stop Overpaying On Freight Invoices
Penny checks every invoice against your contracts and what the shipment actually did, then disputes what doesn’t hold up. You pay 30% of what she saves you, and nothing if she saves nothing.
Found this useful? Share it with your team.
Share on LinkedIn